Citizen Systems CBM-291 Bedienungsanleitung Seite 1

CBM-290/291 User’s ManualUser’s Manual Model CBM-290/291 Japan CBM Corporation

CITIZEN 10 7.3 Date configuration...

CITIZEN 111 OutlineCBM-290 is a Line Thermal printer which can be equipped in a rack and is widely used forvarious data communication, POS terminal an

CITIZEN 122 Basic Specifications2.1 Model classifications CBM-290 - 34 F - ( )

CITIZEN 132.2. SpecificationsITEM CONTENTSPrinting method Line Thermal Dot Printing SystemPrint speed 50 mm / s (MAX)Dot density 8 Dots / mm (Verti

CITIZEN 142.3. Specifications of Roll paper2.3.1. Recommended paper Type : Thermal Paper Paper width : 58 + 0, - 1 mm Paper

CITIZEN 152.4 Specified Power SupplyThe following specifications is required for Power supply.VCC : DC 5V ± 5% 0.2 - 0.5 AVP : DC24V±5% 2 - 3 A (6A o

CITIZEN 162.5.2 Explanation of each partsl Front cover Open/close this cover in case of paper change or paper jam.l Paper lamp Lights up when

CITIZEN 173 Operation3.1 Rack mounting(1) Put the main body into the rack as shown in the following drawing.(2) Hold the main body from rear side with

CITIZEN 183.2 Connecting a cable for power supply and interface(1) Make sure that main power supply is turned OFF before connecting this cable.(2) Pre

CITIZEN 193.3 Opening/closing front cover(1) Applying your finger on the projection on the left side of the front panel, pull it forward when the l

CITIZEN 2<Important safety instruction>l Read all of these instructions and save them for later reference.l Follow all warnings and instructio

CITIZEN 203.5 Auto paper loading function This printer equips a function to feed the paper automatically when a new paper for replacement is inser

CITIZEN 21 3.7 Removing paper jam and canceling cutter lock Remove paper jam or cancel cutter lock by following the procedure explained below.(1) O

CITIZEN 22l Auto paper cutter lock, paper jam.Turn OFF power supply and clear the problem. To make printer ready for print, turn ON power again after

CITIZEN 234. Dip switch setting Dip switch locates on the rear side of main body. Make sure that power is turned OFF before changing Dip switch se

CITIZEN 245. Connecting connector Configuration of the connector for power and interface which is packed in this box is as follows. Make sure to c

CITIZEN 255.2 Precautions1. For LED ERROR , there is a resister of 330 Ohm on the circuit side to make current value 10 mA. Please use LED which its

CITIZEN 26 6.3 Electrical characteristics (1) Input Signal Level All the input signals are at TTL level. "HIGH" level

CITIZEN 276.4 Timing chart(1) Data Input and Printing Timing ACK is not outputted. T1,

CITIZEN 287 Serial Interface 7.1 Specifications (1) Data transfer system: Asynchronous (2) Baud rates 1200, 2400, 4800, 9600, 19200 bps

CITIZEN 297.2 Explanation of Input / Output signals 7.2.1 Input / Output signals (1) RD Serial receiving data signal. On occurrence of framing

CITIZEN 3IMPORTANT: This equipment generates, uses, and can radiate radio frequency energy and if not installed and usedin accordance with the instruc

CITIZEN 30 7.3 Date configuration 1 Start bit 2 Data bit (+ parity bit) 3 Stop bit ( 1

CITIZEN 31 7.5 Data receiving control When DTR/DSR control having been selected, with BUSY signal at "LOW", data from the host sid

CITIZEN 328. Print Control Function8.1 Command LitCONTROLCODEFUNCTION 1HTHorizontal tab command 2CRPrint command 3LFPrinting and paper feed 4ESC SPSet

CITIZEN 338.2 Command Details(1) Horizontal Tab Command (HT) Code : (09)h Shifts the printing position to the next horizontal tab position. The hori

CITIZEN 34 (6) Specifying/Canceling Download Character Set (ESC % n) Code: [1B]h + [25]h + [n] * {0 ≤ n ≤ FF} data is described in Hex code

CITIZEN 35 (8) Specifying the Bit Image Mode (ESC * m n1 n2 D1 - Dn) Code : [1B]h + [2A]h + m + n1 + n2 + Dn * {m= bit image mode (See t

CITIZEN 36 (10) Specifying 1/6 inch line feed rate (ESC 2) Code : [1B]h + [32]hThe line feed rate per line is specified by 1/6 inch. (11) Setting

CITIZEN 37 (15) Specifying/canceling Double Printing (ESC G n) Code : [1B]h + [47]h + n * {0 ≤ n ≤ FF} Data is described in Hex code.Specif

CITIZEN 38 (20) Enabling/Disabling Panel Switch (ESC c 5 n) Code : [1B]h + [63]h + [35]h + n * {0 ≤ n ≤ FF} Data is described in Hex cod

CITIZEN 39 (24) Transmitting the printer status (ESC v) Code : [1B]h + [76]hCurrent printer status is transmitted..l Status sent out consists of

CITIZEN 4<Cautions>1. Before using this equipment, be sure to read this User’s manual thoroughly and save it for future reference.2. Portion

CITIZEN 40 (26) specifying/Canceling Inverted Characters (ESC { ) Code : [1B]h + [7B]h + n * {0 ≤ n ≤ FF} Data is described in Hex code.Sp

CITIZEN 41 (30) Bar Code Printing (GS k n Dn NUL) Code : [1D]h + [6B]h + n + Dn + [00]h * {0 ≤ n ≤ 7} Data are described in Hex code.Sp

CITIZEN 42 (34) Selecting the font of HRI code (GS f n) Code : [1D]h + [66]h + N * n = 0, 1 Selecting the font of HRI code

CITIZEN 43 (36) Printing Download Bit Image (GS / m) Code : [1D]h + [2F]h + m * {0 ≤ m ≤ 3} Data is described in Hex code.Prints download

CITIZEN 44 (39) Data Input Control (ESC = n) Code : [1B]h + [3D]h + n * {0 ≤ n ≤ FF} Data is described in Hex code.Selecting equipment in w

CITIZEN 45 (41) Full Cut (ESC i) Code : [1B]h + [69]hActivating auto cutter (Full cut)l This is valid only when n is inputted at the beginning of

CITIZEN 469. Character Table9.1 International

CITIZEN 479.2 International Character Code Table

CITIZEN 48Appendix 1. Block Diagram

CITIZEN 49Appendix 2. Outer Appearance

CITIZEN 5<! Warning> Do not subject this equipment to excessive force or shocks such as by standing on it, dropping it or hitting it.

CITIZEN 6<! Precautions for installation>1. Do not install or store this printer near fire, water, a heater, in the direct sunshine in the loc

CITIZEN 7 ! Caution label is attached on the following position. Make sure to use this equipment properly. Read the cautions for handling carefull

CITIZEN 8< ! Ordinary Maintenance >1. Make sure to maintain the equipment after switching OFF the power .2. When cleaning the platen of prin

CITIZEN 9Contents1 Outline ..............................